The best replacement water heater for your Atwood G6A-7 is the Fogatti RV Tankless Water Heater item # LSB44FR. This water heater will fit into the Atwood water heater's existing cutout. It has a heating capacity of 41,800 Btu and will give you up to 90 gallons per hour of hot water.
I have linked an installation video below.
This unit is also available in white Fogatti RV Tankless Water Heater item # LSB64FR. view full answer...
The Replacement Door for Atwood RV Water Heaters # AT91386 is 18" wide and 14-1/2" tall(see image). This is a replacement for Atwood model AT96110, AT96163, AT96121, and AT96136 6 gallon water heaters.
We also have the Water Heater Door Latch # 372225 that you may need to replace with the door if it is damaged and no longer securing the door in place while you drive down the road. view full answer...
The largest exterior door available for a Furrion water heater is the 18-1/8" tall x 18-1/8" wide door that comes with the heater you asked about:
- Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 18" x 18" Door # FR68SR
I have added a link below to a video review of this heater for you to check out as well if you'd like to take a look. view full answer...
The Camco Water Heater Element # CAM02143 is what you need for the SW6DEL water heater. According to our research this element will replace the heating element perfectly in your Suburban water heater.
You can also use the Camco RV Water Heater Anode Rod part # CAM11563 to replace the anode. From our research you can also use the Camco RV Water Heater Temperature and Pressure Relief Valve part # CAM10473 to replace the relief valve. view full answer...
The switch for the Atwood RV Water Heater # AT96117 is already mounted to the back of the water tank like what you can see in the attached picture. view full answer...
The Furrion RV Tankless Water Heater item # FR93FR would be a great tankless replacement option for your Atwood GC6AA-93. The Furrion tankless is 12-5/8" tall x 19-3/16" deep x 12-13/16" wide.
You will also need an access door because they come separate due to the different sizes. The best options are the Replacement Access Door for Furrion RV Tankless Water Heater - 18" wide x 16" tall item # FR63FR or 18" x 18" item # FR73FR.
The Dometic RV Water Heater item # DMC74FR you referenced... view full answer...
I went out to our warehouse to take a look at the Atwood Replacement RV Water Heater Door # AT91386 referenced in your question. The door measures 18 inches wide and right at 14-1/2 inches tall. This particular replacement door is designed for the Atwood water heater models AT96110, AT96163, AT96121, and AT96136. view full answer...
Yes, there is. It is the Furrion RV Tankless Water Heater item # FR48SR which is gas only. This tankless hot water heater measures 12-5/8L x 12-13/16W x 19-3/16D so it should fit right into your existing cutout with little to no modifications needed.
This is also available in black item # LSB44FR. view full answer...
The amperage draw of the Atwood RV Water Heater w/ Heat Exchange # AT96163 that you referenced is 11.6 amps. The heating capacity of this is 8,800 Btu as well. view full answer...
I took a look at the instructions, and a separate inlet check valve is not required for the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU # FR93FR. view full answer...
I reached out to my contact at Camco and they only make the 8 inch and 12 inch hoses. Valterra is the other manufacturer we carry that has those bypass hoses and they are 8-1/2 inches end to end or 12-13/4 inches according to my contact at Valterra. These are the more standard sizes for the 6 gallon and 10 gallon water heaters.
I recommend going with the 12 inch hose found in the Camco RV Winterization Bypass Kit w/ 12" Hose # CAM35963 as that extra length will not be an issue when bypassing... view full answer...
What you see in the photo of the Valterra RV Water Heater By-Pass Kit # P23503LFVP is actually a roll of Teflon thread sealer tape. It does appear to be a thick flat gasket since it is packaged on its side. The 3-way valves use a 1/2-inch female thread that matches the two threaded male ports on each valve. view full answer...
The dimensions are 4-1/2 inches in diameter and 7/8 inch depth for the wall controller of the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 18" x 18" Door # FR68SR. view full answer...
The dimensions of the Replacement Access Door for Fogatti RV Tankless Water Heater # LSB34FR are 15" x 15". I went ahead and attached a diagram that shows these measurements for your convenience. view full answer...
The Hott Rod RV Water Heater Conversion Kit # DGR6VP includes 2 adapters that replace the Atwood Anode Rod/Drain Plug(1/2" NPT) # CAM11553 and Suburban Anode Rod(3/4" NPT) # CAM11563 for the electrical heating element. view full answer...
The reducer bushing on the Camco RV Water Heater Anode Rod part # CAM11533 is a 1/2" NPT fitting. Please note that the outer diameter of the fitting is not the same as NPT. The outer diameter of the threads on a 3/4" NPT fitting is 1.060". For an anode rod with a 3/4" NPT fitting, the only option we have for you is part # CAM11563 which is 9-1/2" long. view full answer...
The Furrion Tankless water heater part # FR48SR that you referenced requires a minimum water pressure of .32 gallons per minute. Which if you need a water pump installed on your setup the Flow Max part # LC689052 would be a really great option. view full answer...